SOL.TECline ZIP Radio

Electronic tubular motor, Ø  45  mm, with radio control

The motor is suitable for these applications

The engine has the following features:

Anti-freeze protection

The motor detects that the blind is frozen to the windowsill and stops the rolling-up process.

Downward block detection

The built-in motor intelligence detects obstacles as the system extends, thereby protecting the equipment.

DualStop-Control

If the system detects an obstacle, the motor moves the blind a set distance in the opposite direction. After two more unsuccessful attempts, the system moves to its safety position (upper limit position). This applies in both the AUF and AB directions.

GEIGER Radio 2.0

The unidirectional radio system offers a long range and enables secure communication with remote receivers.

Obstacle detection in the UP direction

The built-in motor intelligence detects obstacles during retraction, thereby protecting the system.

Pinch protection

This feature prevents fingers or other objects from getting pinched or damaged.

Plug & Play

Automatic detection of end positions without time-consuming adjustment during installation. Completed in just one up and down cycle. Quick and precise adjustment of end positions.

Referencing

Every 50 cycles, a reference run is performed to verify that the end positions are correct. To do this, the curtain is raised until the motor cuts out due to torque. The end positions are checked in this way and, if necessary, readjusted.

Slow motion detection

The motor detects the system’s status and can identify changes in winding behavior. If the blind moves too slowly in the down direction and the bottom rail is in danger of jamming, the motor stops automatically to protect the system and the blind.

Soft position

The blind stops before reaching the top position to protect the materials.

Wind resilience

The obstacle detection system can distinguish between an obstacle and a gust of wind. If a gust of wind blows in the UP direction, the blind moves safely to its upper end position, protecting the system and preventing damage to the blind.

Product advantage

  • Electronic limit switch
  • Easy setup: Plug & Play
  • Can be wired in parallel
  • Plug-in connection cable available in various lengths

Notes

  • The limit positions can be programmed using any control cable. Any control cable that has a programming button or supports simultaneous UP/DOWN commands can be used.
  • Do not use a switch during operation that allows simultaneous UP/DOWN commands, to prevent the learning mode from being activated accidentally.

Options

  • Available with SOC, ROC, or COM heads
  • Available as a high-speed model upon request

Limit switch adjustment

Upper end position

Auf Position

Full stop*

Lower end position

Auf Position

Full stop*

* For roller shutters with a stopper and anti-lift device or a rigid shaft connection

Possible cylinder heads

SOC head
COM head
ROC head

Technical Specifications

SOL.TECline SOC head
SOL.TECline ROC head
SOL.TECline COM head
>
SOL.TECline ZIP Radio GB45F14-__/__GB45F14-10/15GB45F14-20/15GB45F14-30/15GB45F14-40/15GB45F14-50/12
Voltage230 V AC / 50 Hz
Electricity0,47 A0,63 A0,80 A1,00 A1,00 A
Cos Phi>0,95
Inrush current (factor) × 1.2
Performance105 W140 W180 W220 W220 W
Torque10 Nm20 Nm30 Nm40 Nm50 Nm
RPM15 rpm15 rpm15 rpm15 rpm12 rpm
Limit switch range200 revolutions
Protection rating IP44
Total length¹438 mm458 mm488 mm518 mm518 mm
Operating mode S2, 4 min.
Schalldruckpegel²39 dB(A)
Durchmesser45 mm
Weightca. 1,9 kgca. 2,0 kgca. 2,2 kgca. 2,4 kgca. 2,4 kg
Ambient humidity dry, non-condensing
Storage temperatureT = -15°C .. +70°C
¹ SOL.TECline-ROC: +5,9 mm / SOL.TECline-COM: +4,2 mm
² The average sound pressure level values are provided for reference only. The values were measured at GEIGER during idle operation with the drive suspended freely at a distance of 1 m and averaged over 10 seconds. The measurement does not refer to any specific test standard.
Subject to technical changes.